Arwibon Q06Pro Controller Wiring Guide

If you are replacing both controllers on an Arwibon Q06pro, the wiring inside the deck must be reconnected in the correct order. This procedure covers Controller A, Controller B, the front and rear motor Hall connectors, all six high-current phase-wire joints, the main control harnesses, the two charging-port connectors, and the yellow XT60 battery connection.

The wiring layout below follows the official Q06pro controller installation procedure. The connector numbers and wire combinations apply to this specific Q06Pro setup and should not be reused as a universal wiring map for other Arwibon scooter models.

Tools and Materials Needed

• Phillips or Allen screwdriver
• Small open-end wrench, approximately 7–8 mm
• Original black or white insulating sleeves for the phase-wire joints
• Protective gloves

Rear Motor to Controller B

The official procedure starts with the rear motor wiring and connects it to Controller B.

Step 1: Connect No. 1 — Rear Motor Hall Connector

Locate the rear motor white 6-pin Hall connector and the matching Hall connector from Controller B.

Check the wire group before joining the plug.

The procedure shows the Hall wiring in the red, black, blue, green, and yellow color group.

Align the connector guide and locking tab, then push the two halves together until the latch engages.

Do not force the connector if the housings are not aligned.

Step 2: Connect No. 2 — Yellow Phase Wire

Before joining the yellow phase terminals, slide the insulating sleeves onto both wires.

Place the yellow ring terminal from Controller B against the yellow ring terminal from the rear motor.

Insert the bolt and hardware.

Hold the nut with the small wrench while tightening the opposite side with the screwdriver.

The two terminals should sit flat against each other.

Step 3: Connect No. 3 — Green Phase Wire

Slide the insulating sleeve onto the green phase wire before connecting the terminals.

Join the Controller B green ring terminal to the rear motor green ring terminal.

Install and tighten the bolt and nut securely.

Check that the metal terminals remain flat and are not twisted under the fastener.

Step 4: Connect No. 4 — Blue Phase Wire

Fit the insulating sleeve first.

Join the blue Controller B phase terminal to the blue rear motor terminal.

Tighten the bolted joint securely.

Do not move the insulating sleeve over the joint until the hardware has been checked.

Connect the Main Control Harnesses

The next group connects the handlebar controls and the central low-voltage wiring inside the deck.

Step 5: Connect No. 5 — Main Multi-Pin Harness

Locate the wide black multi-pin connector coming from the front control harness.

The official procedure shows a mixed wire group including red, blue, black, orange, white, yellow, and green.

Align the outer guide and locking feature.

Push the connector together until the latch fully engages.

Step 6: Connect No. 6 — 2-Pin Auxiliary Connector

Locate the small black 2-pin plug.

The supplied procedure shows red/black wiring on one side and green/black on the other.

Match the connector shape and locking tab, then push it fully together.

Step 7: Connect No. 7 — Black-to-White 2-Pin Connector

Locate the black 2-pin connector with black/white wiring and the matching white 2-pin connector with red/black wiring.

Align the latch and push the connector fully into place.

Do not pull on the wires after connection. Check the plastic housings instead.

Step 8: Connect No. 8 — Drive-Mode Connector

Locate the small black 2-pin connector shown with black/black wiring on one side and red/yellow on the other.

Align the connector before joining it.

Do not force the plug in the wrong orientation.

Step 9: Connect No. 9 — Transparent-Sleeve Signal Connector

Locate the small 2-pin connector identified by its transparent outer wire covering.

The procedure shows red/white wiring on one side and gray/white on the other.

Connect the two halves until the locking feature engages.

Step 10: Connect No. 10 — Black/Yellow Control Connector

Find the black 2-pin connector shown with black/red wiring on one side and black/yellow on the other.

Align and join the connector.

Check that neither terminal moves backward when the plug is pushed together.

Step 11: Connect No. 11 — Red/Black Control Connector

Locate the next black 2-pin plug.

The official procedure shows black/red wiring on both sides.

Push the connector fully together and check the locking tab.

Front Motor to Controller A

The second controller is Controller A in the supplied installation procedure.

This section connects Controller A to the front motor and to the remaining system harness.

Step 12: Connect No. 12 — Controller A/B Main Link

Locate the wide multi-pin communication connector associated with Controller A.

The procedure shows a mixed group including white, blue, red, black, and green wiring.

Align the guide and push the connector together until it locks.

Step 13: Connect No. 13 — Controller A 2-Pin Control Connector

Locate the small black 2-pin connector.

The supplied procedure shows red/red wiring on one side and blue/green on the other.

Align the locking feature and push it fully into place.

Step 14: Connect No. 14 — Controller A Hall Connector

Find the white 6-pin Hall connector for the front motor.

Match it with the corresponding white Hall connector from Controller A.

Check the wire group and connector orientation before joining them.

Push the two halves together until the latch engages.

Connect the Controller A Phase Wires

The phase-wire arrangement shown in the official Q06Pro procedure is different from the rear motor connection.

Step 15: Connect No. 15 — Yellow to Yellow

Slide the insulating sleeve onto the wiring first.

Join the yellow Controller A phase terminal to the yellow motor terminal.

Before tightening the hardware, keep both wires as straight as practical so the ring terminals are not twisted under load.

Hold the nut with the wrench and tighten the opposite side.

Step 16: Connect No. 16 — Blue to Green

Fit the insulating sleeve before assembling the joint.

Connect the blue phase terminal from Controller A to the green motor phase terminal, following the official procedure.

Keep the wires aligned while tightening the bolt and nut.

Do not change this crossover arrangement to a same-color connection unless you have confirmed a different original wiring configuration.

Step 17: Connect No. 17 — Green to Blue

Slide the insulating sleeve into position before assembling the terminal.

Connect the green phase terminal from Controller A to the blue motor phase terminal.

Tighten the hardware securely while keeping the two wires aligned.

The phase-wire arrangement shown in this Q06Pro procedure is:

• Yellow → Yellow
• Blue → Green
• Green → Blue

Cover All Six Phase-Wire Joints

After the six motor phase terminals have been tightened, inspect each joint before moving the sleeves.

Check that:

• Each ring terminal sits flat
• The bolt and nut are secure
• No terminal is twisted sharply
• No metal connection is loose

Then slide the black or white insulating sleeve over each complete metal joint.

The bolt, nut, and ring terminals should all be covered.

No exposed phase-wire metal should remain inside the deck.

Connect the Battery XT60

After all controller wiring and phase-wire insulation have been completed, install or position the 60V battery in the deck.

Locate the yellow XT60 main battery connector.

Align the keyed connector shape and push the plug fully together.

The yellow XT60 is the main battery connection shown in the official procedure.

For electrical service, it is safer to keep this connector disconnected until the other controller wiring is complete.

Connect the Two Charging-Port Plugs

Locate the two white 2-pin connectors leading to the external charging ports.

The official procedure identifies these as the final two charging-stand connections.

Join each plug to its matching battery-side connector.

Push the housings together until their locks engage.

Arrange the wiring so the connectors are not trapped underneath the battery, controller, or deck cover.

Q06Pro Connector 1–17 Quick Reference

Keep the Phase Wires Straight Before Tightening

The official procedure specifically shows the phase-wire terminals being aligned before the bolt is tightened.

Do not tighten the fastener while the ring terminals are twisted against each other.

A cleaner straight-line arrangement reduces mechanical stress on the terminal and makes it easier to keep the joint fully covered by the insulating sleeve afterward.

Do Not Leave Phase Terminals Exposed

All six bolted phase connections carry motor current.

Once the hardware has been tightened, every metal joint must be covered by its original insulating sleeve.

Do not leave exposed bolts or ring terminals inside the deck.

The scooter vibrates during normal riding, and uninsulated high-current terminals must not be allowed to contact each other or the metal frame.

Check the Controller A Crossover Phase Order Carefully

The official Q06Pro procedure shows Controller A connected with this phase arrangement:

• Yellow to yellow
• Blue to green
• Green to blue

Keep this exact arrangement when following this wiring procedure.

Do not automatically apply the same-color phase sequence used on Controller B.

If the scooter has previously been modified or a different controller version is installed, compare the wiring with the original harness before changing phase order.

Final Electrical Check

Before closing the deck, inspect the complete system again.

Check that:

• Both white Hall connectors are fully locked
• All 17 numbered connections are seated
• Both wide multi-pin connectors are fully latched
• All six phase-wire joints are tight and insulated
• The yellow XT60 connector is fully seated
• Both charging-port plugs are connected
• No wire is trapped under a controller
• No harness crosses a deck-cover bolt hole
• No wire is pressed against a sharp frame edge

Power the scooter on only after the wiring inspection is complete.

If you test the motors, raise both wheels off the ground and begin with a small throttle input.

Arwibon Q06pro Wiring and Parts Compatibility

This procedure applies to the arwibon q06 pro, arwibon q06pro, arwibon q06, and the q06 pro electric scooter wiring configuration shown in the official controller installation procedure.

When ordering arwibon scooter parts, compare Controller A, Controller B, Hall connectors, phase terminals, charging connectors, and control harnesses with the original arwibon q06 pro electric scooter components before installation.

General searches for arwibon scooter, arwibon electric scooter, arwibon scooters, or arwibon e scooter parts may return different controller and wiring versions.

The same applies to arwibon scooter 5600w, arwibon 5600w, and arwibon 5600w adult electric scooter searches. The 5600W description alone does not identify the correct controller version or phase-wire arrangement.

An arwibon scooter charger belongs to the charging system and should be matched separately to the original battery and charging-port specification. Likewise, q06pro electric scooter off road chargers is a charger-related search phrase rather than a controller wiring definition.