How to Open and Remove the Deck Cover on Your Arwibon GT08

Gaining access to the battery compartment is the foundation for all internal maintenance on the arwibon GT08, from battery voltage diagnostics and controller wire harness troubleshooting to lithium pack replacement [00:45]. Engineered as a heavy-duty electric scooter, the arwibon GT08 utilizes a layered deck design consisting of a high-traction silicone foot grip mat and an underlying structural steel/aluminum deck lid secured with perimeter countersunk hex bolts [00:15, 00:25].

Opening the deck without tearing the grip mat or stripping out the internal thread bosses requires the proper tools and a methodical, step-by-step disassembly sequence [00:06, 00:27].

Here is the complete, workshop-tested guide to peeling the silicone mat, unbolting the structural lid, and accessing the internal electrical cavity on your arwibon electric scooter.

Tools and Equipment Checklist

Before beginning the teardown on your arwibon scooter, lay out the following items:

• Fine-Tipped Pick Tool or Toothpick / Wooden Splint: Used to gently lever out and remove the 10 silicone screw-hole dust plugs without gouging the foot mat [00:06, 00:09].

• Metric Hex / Allen Key (3mm or 4mm, L-Shaped or T-Handle): For breaking loose and backing out the perimeter deck plate bolts [00:27, 00:30].

• Clean Microfiber Cloth: To wipe away grit, dirt, and road moisture around the deck seam before lifting the plate.

• Parts Tray or Magnetic Dish: Essential for keeping all 10 perimeter screws and small rubber plugs organized and accounted for.

Understanding the GT08 Deck Construction

The battery deck of your arwibon e scooter features a dual-layer sealed enclosure:

1. Outer Grip Layer: A branded silicone foot mat equipped with circular access cutouts and protective silicone plugs concealing the perimeter fasteners [00:00, 00:15].

2. Structural Lower Lid: A heavy-gauge powder-coated deck plate secured to the main aluminum frame using 10 perimeter countersunk metric bolts (5 on the left edge, 5 on the right edge) [00:24, 00:25].

3. Internal Battery Bay: Houses the primary lithium-ion power pack, dual-drive motor controllers, integrated DC-DC step-down converter, and main power wiring harness [00:45].

Step-by-Step Deck Cover Removal Walkthrough

Step 1: Remove the Protective Silicone Screw Plugs

1. Park the scooter on a clean, level surface or place it securely on a sturdy workstand.

2. Locate the 10 recessed screw positions around the outer perimeter of the silicone footplate: 5 down the left side and 5 down the right side [00:15].

3. Insert the tip of a toothpick or fine pick tool under the edge of each small circular silicone plug [00:02, 00:06].

4. Pry each plug upward and remove it by hand to reveal the countersunk hex bolt hidden underneath [00:03, 00:07].

5. Repeat this process for all 10 plug locations across both sides of the deck and store the plugs in your parts tray [00:10, 00:15].

Step 2: Peel Away the Silicone Deck Mat

1. Starting at the rear corners adjacent to the kickplate, slide your fingertips under the edge of the silicone mat [00:13, 00:14].

2. Carefully peel the mat upward and forward across the entire length of the standing platform [00:21].

3. Set the silicone footpad aside on a clean, flat surface to prevent dust and road grit from adhering to the underside.

Step 3: Remove the Perimeter Deck Plate Fasteners

1. With the structural steel/aluminum deck cover fully exposed, note the 10 perimeter metric hex screws [00:24, 00:25].

2. Insert your 3mm or 4mm hex key firmly into each screw socket [00:27, 00:30].

3. Turn counter-clockwise to break the initial factory torque and back out all 5 screws along the right side [00:27, 00:32].

4. Move to the left side and remove the remaining 5 perimeter screws [00:33, 00:37].

5. Gather all 10 bolts and washers into your parts tray [00:31, 00:37].

Step 4: Lift the Deck Cover to Access the Battery Cavity

1. Grasp the edges of the metal deck plate with both hands near the front and rear corners [00:39].

2. Lift the lid straight upward off the main chassis frame [00:41, 00:44].

3. Tilt the plate away and set it aside to reveal the open battery compartment [00:45].

4. You now have unobstructed access to the lithium battery pack, battery specification labels, dual-motor controllers, and main power wiring harness [00:45, 00:48].

Fastener & Component Disassembly Reference Table

Pro Reassembly & Sealing Tips for Your Arwibon

• Clean the Perimeter Sealing Surface: Before reinstalling the metal cover plate onto your arwibon GT08, wipe the aluminum frame mating flange with a clean rag to remove any dirt, small stones, or water droplets. This ensures a tight seal against rain spray kicked up by the front tire.

• Prevent Cross-Threading: When reinstalling the 10 metal deck screws, thread each one in by hand 2 to 3 turns first before tightening with an Allen wrench [00:37]. Tighten in an alternating cross-pattern from center outward to clamp the plate flat without bowing.

• Re-seat Plugs Firmly: When pressing the silicone dust plugs back into the foot mat cutouts [00:03, 00:07], ensure they seat completely flush with the top surface of the mat. This prevents water and dirt from settling into the screw recesses during wet-weather riding on your arwibon scooters.

• Always Disconnect Battery Power: If you plan to conduct any electrical testing, wire tracing, or component replacements inside the open deck of your arwibon, always disconnect the primary yellow battery connector first to prevent accidental short circuits or electrical arcing.