Arwibon Q30 Electric Scooter Rear Wheel Motor

⚠️ Important Notice:
Arwibon Q30 rear wheel motors have old and new versions. The motor connectors and specifications may be different. Before ordering, please confirm your motor model.

Please provide the motor number before purchase.
The motor number is located on the side of the motor. Please check the label on your original motor and send us a photo for confirmation.

Product Information

48V 2500W Rear Wheel Motor Assembly for Arwibon Q30

This product includes:

• Rear wheel motor assembly
• Motor cover screws
• Motor controller sleeve
• Related screws

⚠️ Note:
This product is a complete rear wheel motor assembly and include the tire.
You do not need to purchase a separate tire. The motor assembly can be installed with your original tire.

Product Features

Original Replacement for Q30

Designed for Arwibon Q30 electric scooter rear drive system. It replaces damaged or worn rear wheel motor assemblies.

Powerful Rear Drive System

The 48V 2500W motor provides the power needed for acceleration, climbing, and daily riding.

Complete Motor Assembly

The package includes the rear wheel motor unit, making replacement easier without rebuilding the motor separately.

Model Confirmation Required

Because Q30 motors have different versions, please confirm:

• Motor number
• Connector type
• Original motor appearance

before ordering.

Arwibon Q30 Rear Wheel Motor Replacement Guide

Tools Required

• Allen wrench set
• Large open-end wrench
• Screwdriver
• Electrical tape (if needed)

How to Remove the Rear Wheel of the Arwibon Q30 Scooter

1. Disconnect Motor Wiring

Before removing the wheel, disconnect the motor cables.

1. Open the battery compartment.
2. Find the rear motor cable connection.
3. Disconnect the yellow 3-pin motor connector (yellow, green, blue thick wires).
4. Disconnect the smaller white signal connector (Hall sensor cable).
5. Make sure the cables are free and can move with the wheel.

2. Remove Rear Brake Caliper

1. Locate the rear brake caliper.
2. Use an Allen wrench to remove the two caliper fixing screws.
3. Carefully remove the brake caliper from the brake disc.

Do not pull or damage the brake cable.

3. Remove Rear Wheel Motor Assembly

1. Use a large wrench to loosen the nuts on both sides of the rear axle.
2. Remove the axle nuts and washers.
3. Hold the rear wheel with both hands.
4. Pull the wheel backward out of the rear frame slot.
5. Carefully pull the motor cable out from the frame.

The old rear wheel motor assembly is now removed.

How to Install the Rear Wheel of the Arwibon Q30 Scooter

1. Install Rear Wheel Assembly

1. Place the new motor wheel into the rear frame slot.
2. Align the motor axle with the mounting position.
3. Route the motor cable through the frame opening.

Make sure the cable is not squeezed by the axle or frame.

2. Tighten Rear Axle

1. Install the original washers.
2. Tighten the axle nuts on both sides.
3. Make sure the wheel is firmly fixed and has no side movement.

3. Install Rear Brake Caliper

1. Place the brake caliper back onto the brake disc.
2. Align the mounting holes.
3. Tighten the two fixing screws with an Allen wrench.

Rotate the wheel by hand and check that the brake disc moves normally.

4. Connect Motor Wiring

Open the battery compartment.

Reconnect:

Motor Power Connector

Connect the yellow 3-pin connector:

• Yellow wire
• Green wire
• Blue wire

Hall Sensor Connector

Connect the white multi-pin signal connector.

Make sure all connectors are fully inserted.

Final Testing

Before riding:

1. Turn on the scooter.
2. Lift the rear wheel off the ground.
3. Test the throttle slowly.
4. Check motor rotation and noise.
5. Test the rear brake.

After confirming everything works normally, close the battery compartment.

Compatible Model

Arwibon Q30 Electric Scooter

Package Includes

• 1 × Rear Wheel Motor Assembly
• Screws and related accessories

Please send your original motor number before purchase to confirm compatibility.