- Choosing a selection results in a full page refresh.
Couldn't load pickup availability
Free Shipping
You may request a return within 30 days of delivery, subject to our return policy. For returns due to a change of mind or other customer-related reasons, return shipping costs are the customer's responsibility. If your item arrives damaged, defective, or incorrect, please contact our support team for assistance. All returns must be approved before the item is shipped back. Please contact our customer service team to start a return request.For complete terms and conditions, please review our Refund Policy.
This display kit is a replacement part for the Arwibon Q06Pro electric scooter. It is intended for replacing the original display when the screen or related wiring needs to be replaced.The kit installs in the original display position and connects to the scooter wiring. Before ordering, please check your scooter model and compare the product photos with the display currently installed on your Q06Pro.
Not sure which part you need? Send us a photo of your scooter, original display, and connector. We can check the part for you before you order.
Before you begin the replacement process, please ensure your scooter is completely powered off and disconnected from the charger for your safety.
Gather the following tools:
Hex keys / Allen wrenches: For loosening and tightening the mounting screws.
Electrical insulation tape: For securing the wire connections.
Heat-shrink tubing: To provide a waterproof seal over the connector.
A heat gun or lighter: To safely shrink the tubing around the wires.
The two videos below show the complete display replacement process, from removing the original screen to installing and protecting the new connection. We recommend watching both videos before you start.
The first video shows how to remove the original display from your Arwibon Q06Pro.
Remove the mounting screws: Use the appropriate tool to loosen the screws holding the display to the handlebar bracket.
Disconnect the display cable: Follow the cable from the display until you reach the connection point. Carefully disconnect the plugs between the display wiring and the scooter wiring.
The second video takes you through the installation of the replacement display.
Route the cable (00:10): Place the new display on the handlebar bracket and feed the display cable through the center of the handlebar as shown in the video.
Secure the display (00:21): Install the two screws behind the display and tighten them to the bracket.
Connect the wiring (00:44): Locate the corresponding connector on the scooter and connect the display wiring. Check the connector position and direction before plugging it in.
Protect the connection (00:54 / 01:15): After connecting the wiring, wrap the connection with insulation tape and use heat-shrink tubing as demonstrated in the video. Make sure the connection area is properly covered to help keep water away from the wiring.
Once the physical installation is complete, please go through these final checks before taking your scooter out for a ride:
Inspect the Mounting: Ensure the display is firmly secured to the handlebar and does not wobble.
Verify the Seal: Double-check that the heat-shrink tubing and electrical tape fully cover the connectors to prevent water damage.
Power On & Test: Turn on the scooter. Check if the screen lights up properly and displays the correct battery level, speed, and riding modes.
Test the Throttle & Buttons: While the scooter is stationary (or propped up), test the buttons to ensure they change modes correctly, and gently test the throttle to confirm it communicates perfectly with the motor.
Solid quality display unit for Q06Pro scooter. All functions work correctly including speed readout and battery indicator. Wiring terminals are well‑made. Only small complaint would be there is no paper instruction manual, but wiring logic is straightforward if you have basic knowledge.
Works great with Arwibon Q06Pro. Digital numbers are sharp and visible day and night. Cable is durable with good insulation. Just note you need to double鈥慶heck each wire connection carefully during installation. Restored full dashboard functionality for my electric scooter.
My old scooter display went dead after water damage. This kit fit my Q06Pro without any issues. Screen is bright and easy to read even under direct sunlight. Cable length is just right for the handlebar mounting. Everything works as original, great spare part.
Exact OEM‑style replacement. Swapped out my faulty old unit in minutes. Screen responds quickly when accelerating. The outer casing feels tough and scratch‑resistant. Now I can track my speed and remaining battery again, very satisfied with this purchase.
Perfect replacement display for my Arwibon Q06Pro. The wiring matches exactly, no extra modification needed. Speed, battery level and mileage all show clearly on the screen. Plug‑and‑play install, fixed my broken original display right away.
Thanks for subscribing!
This email has been registered!
| Product | SKU | Description | Collection | Availability | Product Type | Other Details |
|---|